Dealer and quantity discounts available
Cart 0
JUMBO T-Bar Knob (SILVER) for Penn Int'l 30VSX, 50VSX Reels - Reel Power Handles

JUMBO T-Bar Knob (SILVER) for Penn Int'l 30VSX, 50VSX Reels



New Light Weight 18 degree Articulated Aluminum JUMBO T-Bar KNOB (SILVER) For PENN Int'l 30VSX, 50VSX, 30VSW, 50VSW, 70VSW, 30VW and 50VW Reels.  NOTE: Handle Blank NOT Included.


You are bidding for ONE (1) new Aluminum JUMBO T-Bar Knob, pictured on the right. For comparison purposes, the knob shown on the left is from a PENN 50VW reel.  Which knob would you prefer to have in your hand?

 The knob incorporates a 18 degree offset to provide increased torque.  The knob and handle blank are constructed from 6061 Aluminum and incorporates a ball bearing in the shaft.  The hollow aluminum knob is extremely light weight and incredibly comfortable. The knob weighs about 4oz. and is about 4.25" in length.


To attach the knob to the  original Penn handle blank:  


With a Phillips screw driver, remove the original Penn knob from the handle blank.  The knob shaft is detached from the knob by removing the small allen screw from inside the knob.  Then separate the knob from the shaft.  Remove the small plug from the top of the shaft.  This will expose a slot in the pin for the second screw driver.  Attach the shaft to the original Penn handle blank using 2 screw drivers.  The thin washer MUST be placed next to the shaft and the handle blank and NOT next to the Phillips head screw.  You should use blue Loctite 242 when attaching the knob shaft to the handle blank to secure the screw. Then reverse the procedure to reassemble.

New Light Weight 36mm Diameter Round Aluminum black Power Knob For Most High End Fresh Water Spinning Reels. 

Handle Blank is NOT Included.


You are bidding for ONE new round Aluminum BLACK Power Knob, shown on the left.  This hollow aluminum knob is extremely light weight and incredibly comfortable.   The knob measure 1.42" (36mm) in diameter and weighs about 1oz. A ball bearing is NOT installed in the knob.  For comparision, the knob shown on the right is the 47mm (1.85") knob, of which many thousands I have sold.

Please keep in mind that the Power Knob must be attached to your existing reel handle.  A handle blank is NOT included in this purchase.  However, if you prefer to purchase a complete Power Handle assembly, I have handle blanks for a variety of many popular bait casters and high end spinning reels.  I am offering these complete handles on eBay.


Prior to your purchase, please read the notes below to ensure successful installation.

The knob has an internal pin that will pass thru the handle blank on your reel.  There is a screw that goes into the pin which is used to attach the knob to the reel handle blank.  The exposed part of the internal pin is about 3mm long.   Most reels have a handle blank thickness of at least 4 to 5mm so the exposed pin is longer enough but still will not extended past the handle blank.

Furthermore, the diameter of the pin used on the round knob is 6mm (.236").  After the rivet is removed, enlarge the hole using a size "B" drill bit (.238").  The handle blank must have enough 'meat' to support this larger hole and have place for the base of the 11mm (.43”D) stem. 

Attaching the Knob to the Handle Blank:


To attach the new knob to your handle blank, you must unscrew the two halves of the new knob.  Next, remove the screw and washer from the internal pin at bottom of the stem of the knob.  This is best done using 2 screw drivers, one from the top, the other from the bottom.  Be sure to place a few drops of Loctite Blue 242 into the threads of the internal pin.

Place the knob with the internal pin extended  thru the handle blank.  Attach the screw with washer into the internal pin.   You will then use the 2 screw drivers, one inside the bottom half of the knob and one for the external screw at the bottom, to tighten the knob to the handle blank.  Finally, replace the top half of the knob.  You may want to place a little Loctite Blue 242 on the threads of the knob to avoid loss due to vibration.

Mounting Screws May Be LEFT HANDED!

If Needed, Installation Notes Available Upon Request

Sales Tax: CA Residents Pay 9.25% Sales Tax.

Local Pickup: Local pick-up can be arranged.

Payment: Payment is by PayPal only. Please make your payment without receiving an invoice as the shipping process is keyed on and commences with the receipt of your PayPal payment. If you purchase several items, you may request an invoice prior to payment.
Feedback: Feedback will gladly be left upon receipt of your feedback.


Share this Product

More from this collection